Case for Raspberry Pi Computer.Blue marine Acrylic Plexiglas. 3mm Thick.removable front.with LEGO holes

Features

• Blue marine acrylic 3mm thick (You may have to remove a protective film on parts)
• Top movible
• Adapted for the Rev2 board design. The botton have Mounting Holes
• Full accese for all conectors
• Adapted with holes LEGO pieces.

The Price Was:
Related Products

Product Description

Technical Information

Customer Reviews

Product Description

The case comes as 6 pieces that snap together, made of acrylic.

This ingenious design has no screws or standoffs and there are cute little feet cut into the sides so that it stands up above your desk.

There are engraved labels on all the connector slots.

You can use all of the connectors on the edges of the Pi:HDMI,Audio,Video,SD slot, DSI slot ,micro USB power,Ethernet and the two USB ports.

We also added a slot so that you can connect a 26-pin IDC RIBBON cable to the GP I/O.

The CASE is designed so that you can remove or open the top piece and plug any sort of cables you wish into the breakouts in the middle.

The case is airy enough PI logo that vents and adapted with holes LEGO pieces.

Raspberry Pi computer and other cables or connectors or accessories is not included.

Assembly (see picture)

1.Remove a protective film on parts.

2.There's a small part attached inside the Ethernet and USB cutout - snap this out and set it aside for later.The other small part is for led status used.

3.Peel the protective backing from all parts, With the paper removed.

4.if using a ribbon cable GPIO pins, install this on the board first.The pin 1 stripe should be positioned nearest the corned.

5.Position the first side of the case, with the GPIO side.

6.On the underside of the board, under the Ethernet jack, install the small spacer piece that was snapped out in Step 2.

7.Position the bottom piece over the board, slotting it into the first side. There are no markings on the top or bottom piece.

8.Position the HDMI side of the case.

9.Slide the top of the end piece over the two top hooks first, then, using very light pressure, pivot the end piece downward over the bottom two hooks. If you encounter ANY resistance, stop! Do not force this piece or you will break the plastic.

10.Put the small part on the led.Put the top.

Lego Cases - - Product Reviews, Compare Prices, and Shop at ... ... clear Acrylic Plexiglas. 3mm Thick.removable front.with ... for Raspberry Pi Computer.Blue marine Acrylic Plexiglas. 3mm Thick.removable front.with LEGO holes "lego marines" - Shopping.com $18.00 Case for Raspberry Pi Computer.Blue marine Acrylic Plexiglas. 3mm Thick.removable front.with ... with holes LEGO pieces.Raspberry Pi computer ... Amazon.com: lego marine Case for Raspberry Pi Computer.Blue marine Acrylic Plexiglas. 3mm Thick.removable front.with LEGO holes by guitarreria.com Case for Raspberry Pi Computer.Blue marine Acrylic Plexiglas ... The case comes as 6 pieces that snap together, made of acrylic. This ingenious design has no screws or standoffs and there are cute little feet cut into the sides so ... Cheap Computer Cases, PC Cases: Mid Tower Cases: guitarreria ... ... clear Acrylic Plexiglas. 3mm Thick.removable front.with LEGO ... Raspberry Pi Computer.Blue marine Acrylic Plexiglas. 3mm Thick.removable front.with LEGO holes. Lego in Earrings - Compare Prices, Read Reviews and Buy at Bizrate. Case for Raspberry Pi Computer.Blue marine Acrylic Plexiglas. 3mm Thick.removable front.with LEGO holes. ... made of acrylic. Case for Raspberry Pi Computer.Blue marine Acrylic Plexiglas ... Case for Raspberry Pi Computer.Blue marine Acrylic Plexiglas. 3mm Thick.removable front.with LEGO holes - The case comes as 6 pieces that snap together, made of ...